The fact that it comes with 4 strings means that it will be narrower. One of the best-fretted guitars you can get for your money. The fret design has been around for long and this is so because of its simplicity. With the frets dividing the fingerboard, you'll get to see the position to play each note on the neck. Definitely, makes guitar playing much easier. Warm resonance, comfortable balance and fat tones, that’s the guitar offer to you.
There's a lot to be said for tradition when it comes to the bass guitar, and it's a tradition that ultimately goes back to the originals: the Jazz Bass and Precision Bass. With some stellar options available from Fender and Squier, you're in a good place to get started with those iconic bass guitars. On the other hand, if you'd prefer something a bit more unique, you've got no shortage of options. Over the years, the bass guitar market has grown hugely, and there are now a ton of choices ranging from beginner-friendly instruments like Rogue and Dean models all the way to professional masterpieces from luthiers such as Warwick, Schecter and Rickenbacker.
Much the same considerations apply to bass drum pedals and the stool, but these are not always considered breakables, particularly if changeover time between bands is very limited. Swapping the snare drum in a standard kit can be done very quickly. Replacing cymbals on stands takes longer, particularly if there are many of them, and cymbals are easily damaged by incorrect mounting, so many drummers prefer to bring their own cymbal stands.

A fully electronic kit is also easier to soundcheck than acoustic drums, assuming that the electronic drum module has levels that the drummer has pre-set in her/his practice room; in contrast, when an acoustic kit is sound checked, most drums and cymbals need to be miked and each mic needs to be tested by the drummer so its level and tone equalization can be adjusted by the sound engineer. As well, even after all the individual drum and cymbal mics are soundchecked, the engineer needs to listen to the drummer play a standard groove, to check that the balance between the kit instruments is right. Finally, the engineer needs to set up the monitor mix for the drummer, which the drummer uses to hear her/his instruments and the instruments and vocals of the rest of the band. With a fully electronic kit, many of these steps could be eliminated.

During the 1990s, as five-string basses became more widely available and more affordable, an increasing number of bassists in genres ranging from metal to gospel began using five-string instruments for added lower range—a low "B" string. As well, onboard battery-powered electronics such as preamplifiers and equalizer circuits, which were previously only available on expensive "boutique" instruments, became increasingly available on mid-priced basses. From 2000 to the 2010s, some bass manufacturers included digital modelling circuits inside the instrument on more costly instruments to recreate tones and sounds from many models of basses (e.g., Line 6's Variax bass). A modelling bass can digitally emulate the tone and sound of many famous basses, ranging from a vintage Fender Precision to a Rickenbacker. However, as with the electric guitar, traditional "passive" bass designs, which include only pickups, tone and volume knobs (without a preamp or other electronics) remained popular. Reissued versions of vintage instruments such as the Fender Precision Bass and Fender Jazz Bass remained popular amongst new instrument buyers up to the 2010s. In 2011, a 60th Anniversary P-bass was introduced by Fender, along with the re-introduction of the short-scale Fender Jaguar Bass.
Jump up ^ Tunings such as B–E–A–D (this requires a low "B" string in addition to the other three "standard" strings, and omits the G string), D–A–D–G (a "standard" set of strings, with only the lowest string detuned from E down to D), and D–G–C–F or C–G–C–F (a "standard" set of strings, all of which are detuned either a whole tone, or a whole tone for the three higher-pitched strings and two tones for the E, which is dropped to a low C) give bassists an extended lower range. A tenor bass tuning of A–D–G–C, in which the low E is omitted and a high C is added, provides a higher range.
As the music of the world was evolving, so was the drum set. Tom-tom drums, small crash cymbals, Chinese cymbals and hi-hat cymbals were added to the drum set. The hi-hats were the primary way for the drummers of the big band era to keep time. Before 1930, while playing the New Orleans jazz and Chicago styles, drummers would choke the cymbals on the "ands" of eighth note figures as an alternative to playing a buzz roll, the rim of the drums, or on the woodblocks to keep time. This muting method of keeping time by choking the crash and china cymbals proved to be awkward, so the drummers of that time came up with the idea of having a foot-operated cymbal. This resulted in the creation of the snowshoe cymbal, a foot-operated cymbal. It enabled drummers to play the eighth note figures between the right and left foot, improving the ergonomics and facility of drumset playing and helping drummers to keep a more steady rhythm.
The "Fender Bass" was a revolutionary new instrument for gigging musicians. In comparison with the large, heavy upright bass, which had been the main bass instrument in popular music, folk and country music from the early 1900s to the 1940s, the Fender bass could be easily transported to shows. The bass guitar was also less prone to unwanted feedback sounds when amplified, than acoustic bass instruments.[11] In 1953 Monk Montgomery became the first bass player to tour with the Fender bass guitar, in Lionel Hampton's postwar big band.[12] Montgomery was also possibly the first to record with the bass guitar, on 2 July 1953 with The Art Farmer Septet.[13] Roy Johnson (with Lionel Hampton), and Shifty Henry (with Louis Jordan & His Tympany Five), were other early Fender bass pioneers.[10] Bill Black, playing with Elvis Presley, switched from upright bass to the Fender Precision Bass around 1957.[14] The bass guitar was intended to appeal to guitarists as well as upright bass players, and many early pioneers of the instrument, such as Carol Kaye and Joe Osborn, were originally guitarists.[15]
{ "thumbImageID": "Vintage-Modified-Jazz-Bass-70s-Natural/H99641000002000", "defaultDisplayName": "Squier Vintage Modified Jazz Bass '70s", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Natural", "sku": "sku:site51373037988286", "price": "349.99", "regularPrice": "349.99", "msrpPrice": "549.99", "priceVisibility": "1", "skuUrl": "/Squier/Vintage-Modified-Jazz-Bass-70s-Natural-1373037988286.gc", "skuImageId": "Vintage-Modified-Jazz-Bass-70s-Natural/H99641000002000", "brandName": "Squier", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "", "assetPath": "", "imgAlt": "" } , { "name": "Olympic White", "sku": "sku:site51373037988376", "price": "349.99", "regularPrice": "349.99", "msrpPrice": "549.99", "priceVisibility": "1", "skuUrl": "/Squier/Vintage-Modified-Jazz-Bass-70s-Olympic-White-1373037988376.gc", "skuImageId": "Vintage-Modified-Jazz-Bass-70s-Olympic-White/H99641000003000", "brandName": "Squier", "stickerDisplayText": "Top Rated", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "", "assetPath": "", "imgAlt": "" } , { "name": "Candy Apple Red", "sku": "sku:site51373037988268", "price": "349.99", "regularPrice": "349.99", "msrpPrice": "549.99", "priceVisibility": "1", "skuUrl": "/Squier/Vintage-Modified-Jazz-Bass-70s-Candy-Apple-Red-1373037988268.gc", "skuImageId": "Vintage-Modified-Jazz-Bass-70s-Candy-Apple-Red/H99641000001000", "brandName": "Squier", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "", "assetPath": "", "imgAlt": "" } ] }
The Berklee College of Music in Boston offers training for electric bass players. Electric bass students get private lessons and there is a choice of over 270 ensembles to play in. Specific electric bass courses include funk/fusion styles for bass; slap techniques for electric bass; fingerstyle R&B; five- and six-string electric bass playing (including performing chords); and how to read bass sheet music.[64] Berklee College alumni include Jeff Andrews, Victor Bailey, Jeff Berlin, Michael Manring, and Neil Stubenhaus.[64] The Bass Department has two rooms with bass amps for classes and ten private lesson studios equipped with audio recording gear. Berklee offers instruction for the four-, five-, and six-string electric bass, the fretless bass, and double bass. "Students learn concepts in Latin, funk, Motown, and hip-hop, ... jazz, rock, and fusion."[64]
This guitar has got a maple C-shape neck with a 9.5-inch radius and 20 medium jumbo frets. Most bass playing occurs in the lower fret positions that make 20 frets ideal for bass playing. The single coil feature is quite simple to use and it will create both a bright and focused sound quality. If you are looking for a bass guitar that plays on a small scale, this is just the right one for you.
Extended-range basses (ERBs) are basses with six to twelve strings—with the additional strings used for range rather than unison or octave pairs. A seven-string bass (B0–E1–A1–D2–G2–C3–F3) was built by luthier Michael Tobias in 1987. This instrument, commissioned by bassist Garry Goodman, was an early example of a bass with more than six single course strings. In 1999 South American ERB player Igor Saavedra designed one of the first eight-string ERBs known, and asked Luthier Alfonso Iturra to build it for him. [38] Conklin builds custom ERB basses.[39] The Guitarbass is a ten-string instrument with four bass strings (tuned E–A–D–G) and six guitar strings (tuned E–A–D–G–B–E).[40] Luthier Michael Adler built the first eleven-string bass in 2004 and completed the first single-course 12-string bass in 2005. Adler's 11- and 12-string instruments have the same range as a grand piano.[41] Subcontrabasses, such as C♯–F♯–B–E (the lowest string, C♯0 being at 17.32 Hz at around the limit of human hearing)[42] have been created. Ibanez had released SR7VIISC in 2009, featuring a 30-inch (762 mm) scale and narrower width, and tuned as B–E–A–D–G–C–E; the company dubbed it a cross between bass and guitar.[43][better source needed]
Multi-scale fingerboard is an alternative design for guitars and bass guitars in which the lower-pitched strings gain more length and the higher-pitched strings get shorter, similar to the string lengths on a grand piano. The reason for the uneven scale length across strings is that it evens out the tension across all of the strings, it evens the timbre across the strings, and extending the lower string scales allows the string to produce harmonics that are more in tune with the fundamental[50].

Detuners, such as the Hipshot, are mechanical devices the player operates with the thumb on the fretting hand to quickly retune one or more strings to a pre-set lower pitch. Hipshots typically drop the E-string down to D on a four-string bass.[34] Rarely, some bassists (e.g., Michael Manring) add detuners to more than one string, or even more than one detuner to each string, so they can retune during a performance and access a wider range of chime-like harmonics.

With a basswood body, this can just be the best option if you are trying the guitar for the first time since it has got a short sustain. In addition to this, the guitar can be used for more complicated sounds. If you’re not really sure the kind of music you’ll be focusing on, be sure to try out this guitar. It has twenty frets. Rosewood fretboard and basswood body make it a durable guitar to play on your next rock performance. The maple neck is another good thing about the product.

There are a range of different string types including all-metal strings, which are available in many varieties of winding or finishing, each of which produce different tone, including roundwound, flatwound, halfwound, ground wound, and pressure wound); as well as metal strings with different coverings, such as tapewound and wound with plastic coatings. The variety of materials used in the strings gives bass players a range of tonal options. In the 1950s and early 1960s, bassists mostly used flatwound strings with a smooth surface, which had a smooth, damped sound reminiscent of a double bass. In the late 1960s and 1970s, players began using roundwound bass strings, which produce a brighter tone similar to steel guitar strings, though flatwounds also remained in use by players seeking a vintage tone. Roundwounds have a brighter timbre (tone) with longer sustain than flatwounds.
In other less mainstream genres, such as hardcore punk or metal, the pedagogical systems and training sequences are typically not formalized and institutionalized. As such, many players learn by ear, by copying bass lines from records and CDs, and by playing in a number of bands. Even in non-mainstream styles, though, students may be able to take lessons from experts in these or other styles, adapting learned techniques to their own style. As well, there are a range of books, playing methods, and, since the 1990s, instructional DVDs (e.g., how to play metal bass). In the 2010s, many instructional videos are available online on video-sharing websites such as YouTube.

For musicians like us that play bass, we never seem to get the recognition we deserve! Without us serving up those intricate grooves or beefy low-end riffs, the sound of our bands just wouldn’t be the same! Here at Sam Ash, we want you to know that we truly appreciate you as a bass player no matter what level you’re at or what style or genre of music you play!
Bass bodies are typically made of wood, although other materials such as graphite (for example, some of the Steinberger designs) and other lightweight composite materials have also been used. While a wide variety of woods are suitable for use in the body, neck, and fretboard of the bass guitar, the most common types of wood used are similar to those used for electric guitars; alder, ash or mahogany for the body, maple for the neck, and rosewood or ebony for the fretboard. While these traditional standards are most common, for tonal or aesthetic reasons luthiers more commonly experiment with different tonewoods on basses than with electric guitars (though this is changing), and rarer woods like walnut and figured maple, as well as exotic woods like bubinga, wenge, koa, and purpleheart, are often used as accent woods in the neck or on the face of mid- to high-priced production basses and on custom-made and boutique instruments.
In the 1950s, Leo Fender, with the help of his employee George Fullerton, developed the first mass-produced electric bass guitar.[10] Fender was the founder of Fender Electric Instrument Manufacturing Company, which made popular brands of electric guitars, basses and amplifiers. Fender's Fender Precision Bass, which began production in October 1951, became a widely copied industry standard for the instrument. The Precision Bass (or "P-bass") evolved from a simple, un-contoured "slab" body design and a single coil pickup similar to that of a Telecaster, to a contoured body design with beveled edges for comfort and a split single coil pickup.
In most implementations, a digital piano produces a variety of piano timbres and usually other sounds as well. For example, a digital piano may have settings for a concert grand piano, an upright piano, a tack piano, and various electric pianos such as the Fender Rhodes, the Wurlitzer, and the DX electric piano. Some digital pianos incorporate other basic "synthesizer" sounds such as string ensemble, for example, and offer settings to combine them with piano.

What Are you Looking for?

Digital Piano Bass Guitar Drums
digital piano
bass guitar
piano bass guitar drums

We did the research for you so you won't have to!

All our recommended products have received at least 4.5 stars overall.

Click on any of the buttons above to check them out!