A fully electronic kit is also easier to soundcheck than acoustic drums, assuming that the electronic drum module has levels that the drummer has pre-set in her/his practice room; in contrast, when an acoustic kit is sound checked, most drums and cymbals need to be miked and each mic needs to be tested by the drummer so its level and tone equalization can be adjusted by the sound engineer. As well, even after all the individual drum and cymbal mics are soundchecked, the engineer needs to listen to the drummer play a standard groove, to check that the balance between the kit instruments is right. Finally, the engineer needs to set up the monitor mix for the drummer, which the drummer uses to hear her/his instruments and the instruments and vocals of the rest of the band. With a fully electronic kit, many of these steps could be eliminated.
Since its inception, Virtual Piano has been used as a learning tool in the world’s most prestigious schools – it has helped young children to get a feel for music – it has been the stepping stone for some of the world’s greatest artists. Virtual Piano is fast becoming a form of expression and communication between different cultures and regions of the world – crossing language, space and time. Our vision is to spread the joy of playing the piano to every corner of the globe. Our goal is to engage and inspire people of all ages and abilities, to nurture a passion for music.
Bass bodies are typically made of wood, although other materials such as graphite (for example, some of the Steinberger designs) and other lightweight composite materials have also been used. While a wide variety of woods are suitable for use in the body, neck, and fretboard of the bass guitar, the most common types of wood used are similar to those used for electric guitars; alder, ash or mahogany for the body, maple for the neck, and rosewood or ebony for the fretboard. While these traditional standards are most common, for tonal or aesthetic reasons luthiers more commonly experiment with different tonewoods on basses than with electric guitars (though this is changing), and rarer woods like walnut and figured maple, as well as exotic woods like bubinga, wenge, koa, and purpleheart, are often used as accent woods in the neck or on the face of mid- to high-priced production basses and on custom-made and boutique instruments.
Like the electric guitar, the electric bass guitar is almost always connected to an amplifier and a speaker with a patch cord for live performances. Electric bassists use either a "combo" amplifier, which combines an amplifier and a speaker in a single cabinet, or an amplifier and one or more speaker cabinets (typically stacked, with the amplifier sitting on the speaker cabinets, leading to the term "half-stack" for one cabinet setups and "full stack" for two).
If you’re looking for more traditional hand drums, you can travel the world with our assortment of hand drums from all over the world. Djembes are rich-sounding, African drums that can produce a variety of tones. Check out our selection of doumbeks, Arabic drums, usually made of metal, that provide crisp, melodic cracks and pops. Hand drums and other handheld percussions, like tambourines and shakers, are great for impromptu jam sessions and for kids to learn basic rhythms. Our bongos are fun for reliving the glory of the beat poets of the 1950s, or for a foray into the lively musical traditions of salsa, son, or samba.
The guitar gives you a vintage tone that is delivered by the 3 custom Jaguar single-coil pickups with notched claw shielding rings. Single coils have been around for long and are quite simple. They give you a bright and focused sound. This is truly a unique bass guitar that known as baritone guitar too. You will surely fall in love with the music of the guitar that provided with gritty and low tone sound. It has updated its baritone classics also.
Various electronic bass effects such as preamplifiers, "stomp box"-style pedals and signal processors and the configuration of the amplifier and speaker can be used to alter the basic sound of the instrument. In the 1990s and early 2000s (decade), signal processors such as equalizers, overdrive devices (sometimes referred to as "fuzz bass"), and compressors or limiters became increasingly popular. Modulation effects like chorus, flanging, phase shifting, and time effects such as delay and looping are less commonly used with bass than with electric guitar, but they are used in some styles of music.
Prior to the development of the drum set, drums and cymbals used in military and orchestral music settings were played separately by different percussionists; if the score called for bass drum, triangle and cymbals, three percussionists would be hired to play these three instruments. In the 1840s, percussionists began to experiment with foot pedals as a way to enable them to play more than one instrument, but these devices would not be mass-produced for another 75 years. By the 1860s, percussionists started combining multiple drums into a set. The bass drum, snare drum, cymbals, and other percussion instruments were all struck with hand-held drum sticks. Drummers in musical theater shows and stage shows, where the budget for pit orchestras was often limited, contributed to the creation of the drum set by developing techniques and devices that would enable them to cover the roles of multiple percussionists.
The fretting hand can add vibrato to a plucked or picked note, either a gentle, narrow vibrato or a more exaggerated, wide vibrato with bigger pitch variations. For fretted basses, vibrato is always an alternation between the pitch of the note and a slightly higher pitch. For fretless basses, the player can use this style of vibrato, or they can alternate between the note and a slightly lower pitch, as is done with the double bass and on other unfretted stringed instruments. While vibrato is mostly done on "stopped" notes—that is, notes that are pressed down on the fingerboard—open strings can also be vibratoed by pressing down on the string behind the nut. As well, the fretting hand can be used to "bend" a plucked or picked note up in pitch, by pushing or pulling the string so that the note sounds at a higher pitch. To create the opposite effect, a "bend down", the string is pushed to a higher pitch before being plucked or picked and then allowed to fall to the lower, regular pitch after it is sounded. Though rare, some bassists may use a tremolo bar-equipped bass to produce the same effect.
A common feature of more expensive basses is "neck-through" construction. Instead of milling the body from a single piece of wood (or "bookmatched" halves) and then attaching the neck into a pocket (so-called "bolt-on" design), neck-through basses are constructed first by assembling the neck, which may comprise one, three, five or more layers of wood in vertical stripes, which are longer than the length of the fretboard. To this elongated neck, the body is attached as two wings, which may also be made up of several layers. The entire bass is then milled and shaped. Neck-through construction advertisements claim this approach provides better sustain and a mellower tone than bolt-on neck construction. While neck-through construction is most common in handmade "boutique" basses, some models of mass-produced basses such as Ibanez's BTB series also have neck-through construction. Bolt-on neck construction does not necessarily imply a cheaply made instrument; virtually all traditional Fender designs still use bolt-on necks, including its high-end instruments costing thousands of dollars, and many boutique luthiers such as Sadowsky build bolt-on basses as well as neck-through instruments.